I.C.T-AMV | Multi Group Blades PCB V-cut Machine

| PCB V-cut Machine – Straight, Safe Board Separation

A PCB V-cut Machine does the hard job of parting finished boards without breaking what men and women have spent hours building. The board sits solid while the blade moves or drops, guided by hand or air. Speed comes under the operator’s fingers, slow when care is needed, quicker when the line runs steady. The distance between round top blade and straight bottom blade sets fine to match any V-groove depth. Parts that sit right across the cut line pass through clean. Most important, the push inside the board stays small—solder joints do not split, traces hold, and the whole piece keeps its shape. A Multi Group Blades PCB V-cut Machine that routes or slides may kick up dust, heat the material, and wear faster, but this straight V-cut stays cleaner, cooler, and kinder to the work. Factories that build LED lights, aluminum boards, or FR4 panels choose it because it gets the job done day after day without adding trouble.

I.C.T keeps five solid kinds of V-cut machines ready, each one made for the work at hand:

• Standard manual type: Plain and cheap for small runs.

• Multi-blades separator: Careful steps for long LED strips.

• Guillotine type: Fast drop for thicker, harder boards.

• Move-blade sliding type: Easy shifts for different grooves.

• Multi-knife group type: Handles any length without stopping.

| Feature

Multi-Blades LED Separator

The multi-blades PCB V-cut Machine carries six round blades split into three groups that take turns down the same groove. First group cuts forty percent, second group follows close for the next forty, third group finishes the last twenty in short, easy passes. Each cut being brief, the strain locked in the board drops by eighty percent—no warping on aluminum, no bend in LED strips that cost good money. Blades from Taiwan last more than a year and sharpen many times over. Laser checks keep the tip jump inside 0.02mm so every edge comes even and true. Stainless platforms stretch out to 1.2 or 2.4 meters for long boards; top and bottom blades adjust close; custom blocks hold any width steady. X and Y moves raise the accuracy when needed. In the long runs of LED work, where flat boards mean good product, this machine keeps the line moving and the waste low.

Guillotine Type V-Cut Machine

The guillotine PCB V-cut Machine drops straight with air behind it, holding force under 180 microstrain so solder stays whole and parts nearby take no hit. It cuts clean at the groove edge, only 0.3mm from the closest component, while tall parts up to 60mm clear without trouble. No motor turns, no grinding happens—dust stays down, carbon never forms, metal scraps hardly show. One cut finishes in one second at the foot switch; blade pulls back safe. Six million cuts pass before it needs work, and a quick sanding brings the edge back. FR4 boards and shops that hate dust pick this one because it moves fast, leaves clean lines, and keeps the air clear for the next shift. It stands up to hard daily use without complaint.

Move-Blade (Sliding) V-Cut Machine

The move-blade PCB V-cut Machine lets the operator slide the cut at his own pace, setting blade distance to fit the groove depth exactly. The board stays locked down so parts up to 34mm tall can cross the line safe. Pressure stays low—no cracks start in solder or base. The frame holds heavy and true; blades shape to special jobs if asked. It fits medium shops, trial builds, or places that want plain tools without fancy controls. Hands-on feel lets the worker meet each board as it comes, making clean cuts that hold up in steady production. Low cost and simple upkeep keep it running year after year.

| Specification

Parameter	Manual Single-Blade V-cut Machine	Multi-Blades LED Separator	Guillotine Type V-cut Machine	Move-Blade (Sliding) V-cut Machine	Multi Group Blades PCB V-cut Machine
Operation Type	Manual (hand sliding)	Manual (hand push)	Manual (pneumatic foot switch)	Manual (adjustable sliding)	Manual (multi-group push)
Blade Setup	1 circular + 1 straight blade	6 circular blades (3 groups top/bottom)	Single straight guillotine blade	1 circular + 1 straight (adjustable gap)	Multiple groups of circular blades (custom multi-knife)
PCB Length	0–350 mm	Unlimited (with 1.2m / 2.4m platforms)	0–330 mm	0–350 mm (typical)	Unlimited or very long (platform-dependent)
PCB Thickness	0.8–5 mm	0.2–5 mm	0.3–5 mm	0.8–5 mm	0.2–5 mm (typical for multi-group)
Cutting Method	Single pass sliding	3-phase (40% + 40% + 20%)	One-shot downward cut	Single pass with adjustable depth	Multi-group sequential cutting
Best Application	General PCBs, prototypes, medium volume	Long LED strips, aluminum PCBs, high-volume LED	FR4 boards, clean/dust-free edges	Mixed components, flexible V-depth	Extra-long or wide PCBs, high-efficiency separation

| SMT Line Equipment List

| Customer Success Video

In early 2025, engineer Peter went to Uzbekistan and stayed sixteen days at the customer’s plant, setting up machines and teaching the crew. They bought a full SMT line for automotive motors and parts: 5151 automatic printer, mounter, L8 reflow oven, AOI, NG/OK unloader, BGA rework station, walk-knife depaneler, paste mixer, translation conveyor, and the rest. Space was short, so I.C.T built a U-shaped line that used every foot. Peter walked them through each step until they ran it alone. When he left, production rolled smooth and steady without a hitch.

| Service and Training Support

I.C.T sends full service and training with every PCB V-cut Machine and line. Engineers travel to the site, install right, show how it works, and train the people who will run it every day—operation, cleaning, fixing small troubles, improving flow. Teams learn fast and gain confidence to keep going. After the visit, phone, email, or remote help stays open for quick answers and short stops. This way lines start on time and run long without big breaks.

| Client Testimonials

Customers talk straight about I.C.T engineers—smart, patient, hard-working on the job. They like the PCB V-cut Machine for steady cuts, easy handling of boards, and blades that last. Packing comes careful and strong; machines arrive ready and whole. When trouble shows, answers come quick and right, earning real trust. Many say the gear works hard and the help stays good long after the sale.

| Certifications and Standards

Every PCB V-cut Machine carries CE safety marks, RoHS material rules, ISO9001 quality control, and patents on our own designs. These papers prove the machine meets world standards for safe work, clean build, and steady quality. Shops take them with confidence because they know the build holds up.

| About I.C.T Company and Factory

I.C.T runs its own R&D and factory in Dongguan, China—89 people strong, 20 of them engineers. Started in 2012, it grew fast and now serves over 1600 customers in 72 countries. The 12000m² plant checks every piece hard and follows a full quality system so machines come reliable. One-stop help—from first plan to setup, training, and after—helps shops build lines, fix them, and keep them running strong around the world.