English  |
I.C.T
| Quantity: | |
|---|---|
| Panasonic SMT Assembly Line
I.C.T supplies the Panasonic SMT line from three factories we own and more than 22 years of SMT work. We plan the factory, draw layouts, count workers, show ROI for board makers. The line can be semi-auto or full-auto with loaders, printers, placers, reflow ovens, AOI, unloaders. One operator watches all. Power low at 18Kw/H. We serve factories worldwide. We install in three days with air, power, exhaust, light, 23±0.9°C. We train 7-15 days software, fix, safe. Service 15 years everywhere. This Panasonic SMT line starts quick, grows when needed, keeps cost low, gives good boards long time with steady work and real support.
| Feature
Paste Work
Printer in Panasonic SMT line hold stencil tight, frame fit board right. Change fast no long wait. Auto fill clean print stay same. 3D see paste stop bad come early. Need for thick board many part. Paste many kind work, low heat soft part. Squeegee set pressure even rough copper. Print strong, waste little, new design come quick, result stay same, speed up, fix less, more board come shift.
SMD Placement Technology
Placer in Panasonic SMT line run fast, drop part right on board. Take small 01005 big part no stop. Camera see true every time. Many head place thousand hour. Feeder load auto keep run. Software know board type quick. No mistake close place. Line speed high. Mix batch change easy. Repeat same good. Big volume day no trouble.
Reflow Oven Efficiency
Oven give 12+ zone own air heat even Panasonic SMT line. Nitrogen keep joint clean strong. Profile fit board auto. Cool stop bend. Heat back use 18Kw/H. Screen save all recipe. Conveyor run software speed right, check inside no stop long time, safe move, big make all day, green power.
Inspection and Testing
AOI take 8K picture fast, find wrong part bad solder quick. AI learn every day. Send fix placer now. Cut bad Panasonic SMT line. Report show better. Auto bad side no stop, save all info look quick fix many kind less down, good track, auto note.
| Specification
| Category | Projects | Details |
|---|---|---|
| Factory Layout Requirements | Factory Air Circuit Layout | Use factory air source or separate oil-free compressed air machine. Pressure should be greater than 7kg/cm². |
| Factory Electrical Layout | Single-phase AC220 (220±10%, 50/60Hz) Three-phase AC 380V (380±10%, 50/60Hz) | |
| Factory Exhaust Layout | The minimum flow rate of the exhaust duct is 500 cubic feet per minute (14.15m³/min) | |
| Factory Lighting Layout | The ideal illumination in the factory is 800~1200LUX, at least not less than 300LUX. | |
| Factory Temperature Layout | The ambient temperature of the production workshop is 23±3°C, generally 17~28°C, and the relative humidity is 45%~70%RH. | |
| Material Preparation | BOM List | List all parts and quantities needed for PCBA Production Line assembly. |
| CAD File | Digital design file to plan PCB layout and machine setup. | |
| Gerber File | Standard file for PCB manufacturing and printing stencil. | |
| Solder Paste | Material applied on pads before placing components in printer. | |
| SMD Component Materials | Surface mount parts like chips and resistors for placement. | |
| Industrial Alcohol | Used to clean boards and stencils during setup process. | |
| Splice Belt | Tape to connect feeder reels without stopping the line. | |
| Stencil | Metal sheet with holes to print solder paste accurately. |
| SMT Line Equipment List
I.C.T make real High-Quality PCBA Production Line. Vacuum loader give board clean. Auto printer put paste right. Placer set chip true. Many zone reflow solder hard. Good AOI find all bad. Line stay tight. Yield high. Cost low. No play. Make for hard work car health light. Board come ready real world. We back full.
| Product Name | Purpose in SMT Line |
|---|---|
| PCB Loader | Automatically loads bare PCBs to the line. |
| Solder Paste Printer | Prints solder paste on PCB pads accurately. |
| Pick and Place Machine | Mounts components onto PCBs precisely. |
| Reflow Oven | Melts solder to form solid joints. |
| AOI Machine | Inspects solder joints and placement defects. |
| SPI Machine | Checks solder paste height and quality. |
| Traceability Equipment | Records and tracks production data: Laser Marking Machine/Label Mounter/Inkjet Printer |
| SMT Cleaning Machine | Used for cleaning PCBs, stencils, fixtures, nozzles, etc. |
| Laser PCB Routing Machine | Cut the PCBA into the final product |
| Customer Success Video
In September 2025, I.C.T engineer Roka went to LED lighting factory. Customer want full-automatic Panasonic SMT line 13 machine, 29 meter long, room only 21m × 5m. We make U-shape plan fit 16m × 2.7m perfect. Roka install test 2 day. Train team 6 day. Machine: Vacuum Loader VL-1200, Full-Auto Printer 1200, Conveyor, Pick & Place, L8 Reflow Oven, Cooling Conveyor, Shuttler, AOI AI1238, Unloader, MLS2400 Separator. Next day customer run good LED light board.
| Service and Training Support
I.C.T give full help Panasonic SMT line from first day long time. Team install test 3 day. Engineer train people 7-15 day machine software. Part fast 8 warehouse world. Far fix or man come trouble quick die. Check line regular, new software keep speed. 15 year many language line never stop.
| Client Testimonials
Customer say 2-hour far fix keep Panasonic SMT line run. Oven steady 24/7. Pack safe long trip. Answer come fast. Engineer good over sea. Software easy new man learn quick.
| Certifications and Standards
CE, RoHS, ISO9001, patent every Panasonic SMT line safe clean. Full test before ship work good day one all place.
| About I.C.T Company and Factory
Three factory 12,000m² total. 89 people 20 engineer. 25 year 1600 customer 72 country. Own make new hard test all step warehouse every place. Fast ship good price strong Panasonic SMT line. Door open.
| Panasonic SMT Assembly Line
I.C.T supplies the Panasonic SMT line from three factories we own and more than 22 years of SMT work. We plan the factory, draw layouts, count workers, show ROI for board makers. The line can be semi-auto or full-auto with loaders, printers, placers, reflow ovens, AOI, unloaders. One operator watches all. Power low at 18Kw/H. We serve factories worldwide. We install in three days with air, power, exhaust, light, 23±0.9°C. We train 7-15 days software, fix, safe. Service 15 years everywhere. This Panasonic SMT line starts quick, grows when needed, keeps cost low, gives good boards long time with steady work and real support.
| Feature
Paste Work
Printer in Panasonic SMT line hold stencil tight, frame fit board right. Change fast no long wait. Auto fill clean print stay same. 3D see paste stop bad come early. Need for thick board many part. Paste many kind work, low heat soft part. Squeegee set pressure even rough copper. Print strong, waste little, new design come quick, result stay same, speed up, fix less, more board come shift.
SMD Placement Technology
Placer in Panasonic SMT line run fast, drop part right on board. Take small 01005 big part no stop. Camera see true every time. Many head place thousand hour. Feeder load auto keep run. Software know board type quick. No mistake close place. Line speed high. Mix batch change easy. Repeat same good. Big volume day no trouble.
Reflow Oven Efficiency
Oven give 12+ zone own air heat even Panasonic SMT line. Nitrogen keep joint clean strong. Profile fit board auto. Cool stop bend. Heat back use 18Kw/H. Screen save all recipe. Conveyor run software speed right, check inside no stop long time, safe move, big make all day, green power.
Inspection and Testing
AOI take 8K picture fast, find wrong part bad solder quick. AI learn every day. Send fix placer now. Cut bad Panasonic SMT line. Report show better. Auto bad side no stop, save all info look quick fix many kind less down, good track, auto note.
| Specification
| Category | Projects | Details |
|---|---|---|
| Factory Layout Requirements | Factory Air Circuit Layout | Use factory air source or separate oil-free compressed air machine. Pressure should be greater than 7kg/cm². |
| Factory Electrical Layout | Single-phase AC220 (220±10%, 50/60Hz) Three-phase AC 380V (380±10%, 50/60Hz) | |
| Factory Exhaust Layout | The minimum flow rate of the exhaust duct is 500 cubic feet per minute (14.15m³/min) | |
| Factory Lighting Layout | The ideal illumination in the factory is 800~1200LUX, at least not less than 300LUX. | |
| Factory Temperature Layout | The ambient temperature of the production workshop is 23±3°C, generally 17~28°C, and the relative humidity is 45%~70%RH. | |
| Material Preparation | BOM List | List all parts and quantities needed for PCBA Production Line assembly. |
| CAD File | Digital design file to plan PCB layout and machine setup. | |
| Gerber File | Standard file for PCB manufacturing and printing stencil. | |
| Solder Paste | Material applied on pads before placing components in printer. | |
| SMD Component Materials | Surface mount parts like chips and resistors for placement. | |
| Industrial Alcohol | Used to clean boards and stencils during setup process. | |
| Splice Belt | Tape to connect feeder reels without stopping the line. | |
| Stencil | Metal sheet with holes to print solder paste accurately. |
| SMT Line Equipment List
I.C.T make real High-Quality PCBA Production Line. Vacuum loader give board clean. Auto printer put paste right. Placer set chip true. Many zone reflow solder hard. Good AOI find all bad. Line stay tight. Yield high. Cost low. No play. Make for hard work car health light. Board come ready real world. We back full.
| Product Name | Purpose in SMT Line |
|---|---|
| PCB Loader | Automatically loads bare PCBs to the line. |
| Solder Paste Printer | Prints solder paste on PCB pads accurately. |
| Pick and Place Machine | Mounts components onto PCBs precisely. |
| Reflow Oven | Melts solder to form solid joints. |
| AOI Machine | Inspects solder joints and placement defects. |
| SPI Machine | Checks solder paste height and quality. |
| Traceability Equipment | Records and tracks production data: Laser Marking Machine/Label Mounter/Inkjet Printer |
| SMT Cleaning Machine | Used for cleaning PCBs, stencils, fixtures, nozzles, etc. |
| Laser PCB Routing Machine | Cut the PCBA into the final product |
| Customer Success Video
In September 2025, I.C.T engineer Roka went to LED lighting factory. Customer want full-automatic Panasonic SMT line 13 machine, 29 meter long, room only 21m × 5m. We make U-shape plan fit 16m × 2.7m perfect. Roka install test 2 day. Train team 6 day. Machine: Vacuum Loader VL-1200, Full-Auto Printer 1200, Conveyor, Pick & Place, L8 Reflow Oven, Cooling Conveyor, Shuttler, AOI AI1238, Unloader, MLS2400 Separator. Next day customer run good LED light board.
| Service and Training Support
I.C.T give full help Panasonic SMT line from first day long time. Team install test 3 day. Engineer train people 7-15 day machine software. Part fast 8 warehouse world. Far fix or man come trouble quick die. Check line regular, new software keep speed. 15 year many language line never stop.
| Client Testimonials
Customer say 2-hour far fix keep Panasonic SMT line run. Oven steady 24/7. Pack safe long trip. Answer come fast. Engineer good over sea. Software easy new man learn quick.
| Certifications and Standards
CE, RoHS, ISO9001, patent every Panasonic SMT line safe clean. Full test before ship work good day one all place.
| About I.C.T Company and Factory
Three factory 12,000m² total. 89 people 20 engineer. 25 year 1600 customer 72 country. Own make new hard test all step warehouse every place. Fast ship good price strong Panasonic SMT line. Door open.
