English  |
I.C.T
| Quantity: | |
|---|---|
| SMT Line Machine Solution
I.C.T supplies a complete SMT line machine from three owned factories and over 22 years of SMT work. We plan the factory, draw layouts, count workers, and show ROI for board makers. Lines can be semi-auto or full-auto with loaders, printers, placers, reflow ovens, AOI, unloaders. One operator runs all. Power low at 18Kw/H. We serve factories worldwide. We install in 3 days with air, power, exhaust, light, 23±0.9°C. We train 7-15 days software, fix, safe. Service 15 years all places. This SMT line machine starts quick, grows when needed, keeps cost down, gives good boards steady.
| Feature
Paste Put
Printer in SMT line machine hold stencil tight, frame fit board right. Change fast no long wait. Auto fill clean print stay same. 3D see paste stop bad come early. Need for thick board many part. Paste many kind work, low heat soft part. Squeegee set pressure even rough copper. Print strong, waste little, new design come quick, result stay same, speed up, fix less, more board come shift.
SMD Placement Technology
Placer in SMT line machine run fast, drop part right on board. Take small 01005 big part no stop. Camera see true every time. Many head place thousand hour. Feeder load auto keep run. Software know board type quick. No mistake close place. Line speed high. Mix batch change easy. Repeat same good. Big volume day no trouble.
Reflow Oven Efficiency
Oven give 12+ zone own air heat even SMT line machine. Nitrogen keep joint clean strong. Profile fit board auto. Cool stop bend. Heat back use 18Kw/H. Screen save all recipe. Conveyor run software speed right, check inside no stop long time, safe move, big make all day, green power.
Inspection and Testing
AOI take 8K picture fast, find wrong part bad solder quick. AI learn every day. Send fix placer now. Cut bad SMT line machine. Report show better. Auto bad side no stop, save all info look quick fix many kind less down, good track, auto note.
| Specification
| Category | Projects | Details |
|---|---|---|
| Factory Layout Requirements | Factory Air Circuit Layout | Use factory air source or separate oil-free compressed air machine. Pressure should be greater than 7kg/cm². |
| Factory Electrical Layout | Single-phase AC220 (220±10%, 50/60Hz) Three-phase AC 380V (380±10%, 50/60Hz) | |
| Factory Exhaust Layout | The minimum flow rate of the exhaust duct is 500 cubic feet per minute (14.15m³/min) | |
| Factory Lighting Layout | The ideal illumination in the factory is 800~1200LUX, at least not less than 300LUX. | |
| Factory Temperature Layout | The ambient temperature of the production workshop is 23±3°C, generally 17~28°C, and the relative humidity is 45%~70%RH. | |
| Material Preparation | BOM List | List all parts and quantities needed for PCBA Production Line assembly. |
| CAD File | Digital design file to plan PCB layout and machine setup. | |
| Gerber File | Standard file for PCB manufacturing and printing stencil. | |
| Solder Paste | Material applied on pads before placing components in printer. | |
| SMD Component Materials | Surface mount parts like chips and resistors for placement. | |
| Industrial Alcohol | Used to clean boards and stencils during setup process. | |
| Splice Belt | Tape to connect feeder reels without stopping the line. | |
| Stencil | Metal sheet with holes to print solder paste accurately. |
| SMT Line Equipment List
I.C.T make real High-Quality PCBA Production Line. Vacuum loader give board clean. Auto printer put paste right. Placer set chip true. Many zone reflow solder hard. Good AOI find all bad. Line stay tight. Yield high. Cost low. No play. Make for hard work car health light. Board come ready real world. We back full.
| Product Name | Purpose in SMT Line |
|---|---|
| SMT Line | Total Full automatic SMT Line |
| PCB Loader | Automatically loads bare PCBs to the line. |
| Solder Paste Printer | Prints solder paste on PCB pads accurately. |
| Pick and Place Machine | Mounts components onto PCBs precisely. |
| Reflow Oven | Melts solder to form solid joints. |
| AOI Machine | Inspects solder joints and placement defects. |
| Customer Success Video
In September 2025, I.C.T successfully delivered a full-automatic SMT LED production line to a home LED lighting factory in Saudi Arabia. Engineer Roka traveled to the customer site for installation and training services. The client required a line with 13 machines (total 29 meters), but the space was only 21m × 5m. We designed a U-shape layout fitting perfectly in 16m × 2.7m to meet their needs. After 2 days of installation and debugging plus 6 days of hands-on equipment training and technical support, Roka completed the handover smoothly. Equipment included Vacuum Loader VL-1200, Full-Auto Printer 1200, Conveyor, Pick & Place, L8 Reflow Oven, Cooling Conveyor, Shuttler, AOI AI1238, Unloader, and MLS2400 Separator. The customer began stable, high-quality LED lighting production immediately.
| Service and Training Support
I.C.T give full help SMT line machine from first day long time. Team install test 3 day. Engineer train people 7-15 day machine software. Part fast 8 warehouse world. Far fix or man come trouble quick die. Check line regular, new software keep speed. 15 year many language line never stop.
| Client Testimonials
Customer say 2-hour far fix keep SMT line machine run. Oven steady 24/7. Pack safe long trip. Answer come fast. Engineer good over sea. Software easy new man learn quick.
| Certifications and Standards
CE, RoHS, ISO9001, patent every SMT line machine safe clean. Full test before ship work good day one all place.
| About I.C.T Company and Factory
Three factory 12,000m² total. 89 people 20 engineer. 25 year 1600 customer 72 country. Own make new hard test all step warehouse every place. Fast ship good price strong SMT line machine. Door open.
| SMT Line Machine Solution
I.C.T supplies a complete SMT line machine from three owned factories and over 22 years of SMT work. We plan the factory, draw layouts, count workers, and show ROI for board makers. Lines can be semi-auto or full-auto with loaders, printers, placers, reflow ovens, AOI, unloaders. One operator runs all. Power low at 18Kw/H. We serve factories worldwide. We install in 3 days with air, power, exhaust, light, 23±0.9°C. We train 7-15 days software, fix, safe. Service 15 years all places. This SMT line machine starts quick, grows when needed, keeps cost down, gives good boards steady.
| Feature
Paste Put
Printer in SMT line machine hold stencil tight, frame fit board right. Change fast no long wait. Auto fill clean print stay same. 3D see paste stop bad come early. Need for thick board many part. Paste many kind work, low heat soft part. Squeegee set pressure even rough copper. Print strong, waste little, new design come quick, result stay same, speed up, fix less, more board come shift.
SMD Placement Technology
Placer in SMT line machine run fast, drop part right on board. Take small 01005 big part no stop. Camera see true every time. Many head place thousand hour. Feeder load auto keep run. Software know board type quick. No mistake close place. Line speed high. Mix batch change easy. Repeat same good. Big volume day no trouble.
Reflow Oven Efficiency
Oven give 12+ zone own air heat even SMT line machine. Nitrogen keep joint clean strong. Profile fit board auto. Cool stop bend. Heat back use 18Kw/H. Screen save all recipe. Conveyor run software speed right, check inside no stop long time, safe move, big make all day, green power.
Inspection and Testing
AOI take 8K picture fast, find wrong part bad solder quick. AI learn every day. Send fix placer now. Cut bad SMT line machine. Report show better. Auto bad side no stop, save all info look quick fix many kind less down, good track, auto note.
| Specification
| Category | Projects | Details |
|---|---|---|
| Factory Layout Requirements | Factory Air Circuit Layout | Use factory air source or separate oil-free compressed air machine. Pressure should be greater than 7kg/cm². |
| Factory Electrical Layout | Single-phase AC220 (220±10%, 50/60Hz) Three-phase AC 380V (380±10%, 50/60Hz) | |
| Factory Exhaust Layout | The minimum flow rate of the exhaust duct is 500 cubic feet per minute (14.15m³/min) | |
| Factory Lighting Layout | The ideal illumination in the factory is 800~1200LUX, at least not less than 300LUX. | |
| Factory Temperature Layout | The ambient temperature of the production workshop is 23±3°C, generally 17~28°C, and the relative humidity is 45%~70%RH. | |
| Material Preparation | BOM List | List all parts and quantities needed for PCBA Production Line assembly. |
| CAD File | Digital design file to plan PCB layout and machine setup. | |
| Gerber File | Standard file for PCB manufacturing and printing stencil. | |
| Solder Paste | Material applied on pads before placing components in printer. | |
| SMD Component Materials | Surface mount parts like chips and resistors for placement. | |
| Industrial Alcohol | Used to clean boards and stencils during setup process. | |
| Splice Belt | Tape to connect feeder reels without stopping the line. | |
| Stencil | Metal sheet with holes to print solder paste accurately. |
| SMT Line Equipment List
I.C.T make real High-Quality PCBA Production Line. Vacuum loader give board clean. Auto printer put paste right. Placer set chip true. Many zone reflow solder hard. Good AOI find all bad. Line stay tight. Yield high. Cost low. No play. Make for hard work car health light. Board come ready real world. We back full.
| Product Name | Purpose in SMT Line |
|---|---|
| SMT Line | Total Full automatic SMT Line |
| PCB Loader | Automatically loads bare PCBs to the line. |
| Solder Paste Printer | Prints solder paste on PCB pads accurately. |
| Pick and Place Machine | Mounts components onto PCBs precisely. |
| Reflow Oven | Melts solder to form solid joints. |
| AOI Machine | Inspects solder joints and placement defects. |
| Customer Success Video
In September 2025, I.C.T successfully delivered a full-automatic SMT LED production line to a home LED lighting factory in Saudi Arabia. Engineer Roka traveled to the customer site for installation and training services. The client required a line with 13 machines (total 29 meters), but the space was only 21m × 5m. We designed a U-shape layout fitting perfectly in 16m × 2.7m to meet their needs. After 2 days of installation and debugging plus 6 days of hands-on equipment training and technical support, Roka completed the handover smoothly. Equipment included Vacuum Loader VL-1200, Full-Auto Printer 1200, Conveyor, Pick & Place, L8 Reflow Oven, Cooling Conveyor, Shuttler, AOI AI1238, Unloader, and MLS2400 Separator. The customer began stable, high-quality LED lighting production immediately.
| Service and Training Support
I.C.T give full help SMT line machine from first day long time. Team install test 3 day. Engineer train people 7-15 day machine software. Part fast 8 warehouse world. Far fix or man come trouble quick die. Check line regular, new software keep speed. 15 year many language line never stop.
| Client Testimonials
Customer say 2-hour far fix keep SMT line machine run. Oven steady 24/7. Pack safe long trip. Answer come fast. Engineer good over sea. Software easy new man learn quick.
| Certifications and Standards
CE, RoHS, ISO9001, patent every SMT line machine safe clean. Full test before ship work good day one all place.
| About I.C.T Company and Factory
Three factory 12,000m² total. 89 people 20 engineer. 25 year 1600 customer 72 country. Own make new hard test all step warehouse every place. Fast ship good price strong SMT line machine. Door open.
