Publish Time: 2026-11-19 Origin: Site
During the week of November 9, 2026, I.C.T began on-site technical support for an electronics manufacturing services (EMS) customer in Indonesia. The project covered an R131H radial insertion machine and an PCB loader supplied for security screening and medical equipment control board production. From November 11 through November 18, I.C.T engineer Max worked with the customer’s engineers on installation, programming, production trials, and maintenance training.
The work focused on getting the customer’s own boards running and teaching the team how to set up the next product themselves. That meant working through board support, component orientation, material feeding, and product changeovers at the machine.
The customer manufactures control boards for security screening equipment and medical devices. These boards include through-hole components, making automatic radial insertion part of the assembly process.
One product contained 448 components to be inserted. With that many insertion positions on a board, accurate coordinates, correct component orientation, and secure PCB positioning were central to the setup.
I.C.T supplied the following equipment:
| Equipment | Model | Role in the Process |
|---|---|---|
| Automatic radial insertion machine | R131H | Inserts radial through-hole components into the PCB and cuts and clinches the leads underneath |
| PCB loader | L460L | Feeds PCBs from magazines into the insertion equipment |
The on-site service brought the two machines into operation together and adapted the setup to the customer’s actual boards.
Max began by helping the team connect and verify the power supplies: three-phase 380 V for the insertion machine and single-phase 220 V for the loader. He then checked the machine position, leveled the equipment, and secured the leveling feet.
Next came the feeder supports and machine accessories. Using the supplied calibration fixture, he checked the camera offset before adjusting the board-loading mechanism and testing PCB entry and exit.
These checks established the starting point for product programming and trial production.
The first product required more than entering coordinates. Its 270 × 400 mm PCB had no handling rails, and the initial loading orientation left the center of the board insufficiently supported. During insertion, the board moved vertically, causing insertion errors.
Max discussed inserting the components before depaneling. However, the customer’s existing depaneling fixture was designed for bare boards and could not accommodate the populated assembly. He therefore changed the PCB orientation, readjusted the conveyor rails and fixing positions, and revised the insertion coordinates.
The team also checked component orientation against the actual assembly. After correcting the angle settings, they repeated the production test, and the customer confirmed the component orientation was correct.
Production trials gave the team a chance to check the setup under repeated operation. When a board-transfer fault appeared, Max traced it to the transfer sensor and readjusted it. The service record then documented a continuous run of 101 PCBs.
Further trials covered two products, with 30 boards produced for each. During these runs, the team found that unevenly cut PCB edges could make individual boards fit too tightly in the conveyor rails. Max explained how consistent board width and smooth edges affect board positioning and transfer.
A separate 400 × 500 mm, 2.6 mm-thick PCB required an additional holding solution. I.C.T identified the need for a custom hold-down arrangement and evaluated a pneumatic clamping option for that application.
Training started with the equipment itself: the PCB transport system, insertion mechanism, component feeding system, forming mechanism, and bottom lead-clinching assembly. Max demonstrated feeder installation and removal, then explained the software screens for production, configuration, statistics, calibration, and manual axis control.
The customer’s lead engineer practiced creating NC coordinate files and component data files, setting up panelized boards, and checking PCB and component angles. Max stayed beside the machine to guide the work and explain missed steps when a program did not run as expected.
As training progressed, the engineer changed between two products and adjusted the setup himself. He also began showing another team member how to create programs.
Boards with more than 400 insertion positions require frequent material replenishment. Max demonstrated how to join a new component tape to the remaining tape while preserving the feed holes. He also explained how to add material reels and update the corresponding settings.
Loader training covered magazine adjustment, control-panel operation, and the board-pushing mechanism. When feeding was uneven, Max adjusted the push-cylinder angle and demonstrated the effect on board entry.
Maintenance training included machine calibration with the supplied fixture, camera-offset adjustment, and replacement of wear parts.
Max demonstrated removal and installation of the bottom clinching and lead-cutting blades, explaining the alignment checks required afterward. On the final service day, the customer’s engineer carried out the blade replacement himself under guidance. The team then ran production tests and confirmed normal operation after the replacement.
Both the R131H radial insertion machine and L460L PCB loader passed equipment acceptance on November 18, 2026.
By the end of the visit, the customer’s lead engineer could create product programs and component databases, adjust the machine, replenish materials, perform calibration, and carry out routine maintenance. The final hands-on blade replacement and production test provided a practical check of those maintenance skills.
The visit also identified follow-up needs for the larger PCB and recommended an exit conveyor so operators could collect finished boards without reaching into the machine.
The service report records active participation from the customer’s engineers throughout the visit. They took notes, practiced programming and changeovers, and gradually took on more of the setup work themselves. A customer feedback video was also recorded near the end of the service.
For this project, the handover included both functioning equipment and engineers who had practiced using and maintaining it with their own products. I.C.T’s on-site technical support helped the customer move from initial installation to running production trials and managing everyday setup tasks.
Planning automatic through-hole insertion for your control boards? Share your PCB dimensions, component list, and production requirements with I.C.T to discuss equipment selection and technical support.